Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Ontario?
Gate parts and welding in Ontario typically run $150 to $650 for common repairs, and most jobs land closer to $200 – $400 once parts and labor are combined. A single worn hinge, a snapped weld on a post bracket, or a replacement roller can be done for under $300. Full gate-frame welding, bent-track straightening, or storm-damaged rebuilds get into the $600 and up range. Prices here move with the part, the gate material, and how far the damage has spread before someone diagnoses it.
We specialize exclusively in gates, which means the number we give you reflects the actual part cost and the actual labor in Ontario, not a phone guess. Give us a call at (855) 707-3634 and we’ll schedule a free estimate.
Gate Parts & Welding Cost Breakdown (2026)
Here’s what Ontario property owners are paying this year. These ranges assume a standard residential swing or slide gate; commercial operators and heavy steel typically sit at the upper end or above.
| Job | Typical Cost Range | Notes |
|---|---|---|
| Hinge replacement (per hinge) | $95 – $185 | Includes weld removal and re-weld; heavier commercial hinges cost more. |
| Roller / wheel replacement (per roller) | $75 – $140 | Slide gates and track systems; seized rollers usually fail in pairs. |
| Post bracket re-weld | $150 – $275 | Cracked or failed bracket at the frame. Common after ground settling. |
| Gate-frame crack repair (single) | $185 – $350 | Welding a fatigued tube or corner. Includes grinding and refinish prep. |
| Bent track straightening (slide gate) | $250 – $500 | Depends on track length and whether a new section is needed. |
| Full gate re-weld (frame overhaul) | $450 – $900 | Multiple welds, re-hanging, and alignment after re-welding. |
| Gate latch / hardware replacement | $85 – $175 | Latch, striker, or handle set. |
| Operator arm / actuator repair (parts & labor) | $275 – $650 | Common on LiftMaster and FAAC swing operators. Parts vary by brand. |
| Safety sensor / loop detector replacement | $225 – $500 | Access control and safety devices; commercial loops cost more. |
| Control board repair or replacement | $350 – $800 | Common across LiftMaster, Linear, DoorKing, and Elite systems. |
| Emergency / after-hours call | Add $85 – $200 | For gates stuck open or closed when access can’t wait. |
What drives the number up: steel or heavy-gauge aluminum gates that take longer to weld, commercial operators with more complex control stacks, and any job where a seized part has already damaged a neighbor part. What drives it down: catching a failing hinge before it tears a bracket, and having a model and brand on hand so we know the part before we arrive. Our Gate Parts & Welding in Ontario service page covers exactly what we stock and what we fabricate on site.
What Affects Gate Parts & Welding Pricing in Ontario
1. Material and gauge of the gate
A lightweight aluminum residential gate welds faster than a welded-steel commercial gate, and the labor difference shows up on the invoice. Thicker steel needs more passes, more grinding, and a longer cool-down before we can check alignment.
2. Brand and operator model
Parts pricing is not uniform across the nine brands we service. A hinge is a hinge, but a control board, a loop detector, or an actuator arm for a LiftMaster or DoorKing commercial operator costs more than the same category part on a Mighty Mule residential unit. We work across LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so when you tell us the brand you have, we come closer to the actual number before we leave the shop.
3. Whether the part is stock or fabricated
Standard hinges, rollers, latches, and brackets are stocked and priced as parts. A custom bracket, a bent track section, or a one-off repair weld is fabricated or fitted on site, which adds bench time. Older gates and discontinued brands are where fabrication is most likely.
4. Access on site
A gate that a truck can reach easily takes less time than one tucked behind a retaining wall in the Ontario ranch and newer-build neighborhoods where the driveway runs tight. Rewelding an upright post in a cramped corner takes longer than an open driveway, and the labor reflects it.
5. The Inland Empire climate and ground movement
This is one of the real local cost drivers. Ontario’s hot, dry summers and the wet winters we do get put a lot of stress on gate posts set in soil that swells and shrinks. We routinely see post-bracket welds crack on gates that were fine a year earlier, and hinges seize faster in yards with dust and dry grit blowing into the pivot points. The climate doesn’t change the price of a part, but it’s why local gate hardware fails sooner than it does in a milder climate, which pushes more Ontario property owners into repair calls each year.
6. Residential vs. commercial duty
A commercial slide gate with an access-control loop, safety edges, and a DoorKing operator carries heavier parts and more diagnostic time than a single residential swing gate with a Ghost Controls arm. If your property is a multi-unit complex, an industrial yard, or a gated community, budget toward the upper end of every range above.
How to Save on Gate Parts & Welding
The biggest savings come from calling before a small problem spreads. Here’s what actually moves the number down:
- Fix the first crack, not the last. A post-bracket re-weld at $150 – $275 is cheaper than waiting until the frame around it fatigues and you’re into a $450 – $900 overhaul.
- Replace seized rollers in pairs. One seized roller drags the healthy one and the track. Doing both at once avoids a second visit.
- Know your brand and model. Snap a photo of the operator label on the arm or control box. When we know it’s a BFT or Linear unit before arrival, we bring the right part and skip the diagnostic trip.
- Bundle the work. If a hinge is failing and a latch is sticking, do both in one scheduled visit rather than two separate calls.
- Stay ahead of the dry season. A quick hardware check in early spring, before the summer heat and dust seize up your pivots, catches most failures before they cost real money.
Our estimates are free, and the number we quote comes from an on-site diagnosis, not a phone guess. Call (855) 707-3634 to schedule.
FAQs – Gate Parts & Welding Cost
How much does it cost to repair a gate in Ontario?
Most gate repairs in Ontario run $150 – $400, with the average landing around $250 for a hinge, roller, latch, or single bracket weld. Frame cracks and bent tracks push toward $350 – $500. Call (855) 707-3634 for an exact figure based on an on-site diagnosis.
Is it cheaper to repair or replace a gate?
Repair is cheaper in the large majority of cases. A $200 – $400 weld or hardware job beats a $2,000+ full gate replacement unless the frame is rusted through or the gate is structurally bent beyond straightening. We’ll tell you plainly which one you’re facing. Call (855) 707-3634 for a free assessment.
Do you repair electric gate operators too, or just welding?
Both. Operator and control work starts around $275 for an actuator arm repair and runs to $800 for a control board replacement, on top of the mechanical welding. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule operators. Call (855) 707-3634 to book.
How much does a new control board for a gate cost?
A gate control board replacement in Ontario typically costs $350 – $800 depending on the brand and operator model. Commercial DoorKing and LiftMaster boards sit at the upper end. Call (855) 707-3634 with your brand and model and we’ll give you a tighter estimate.
Can you come out the same day?
Often, yes, subject to scheduling. Emergency calls for gates stuck open or stuck closed carry an add-on of $85 – $200, and the sooner a failing hinge or bracket is caught, the cheaper the fix. Call (855) 707-3634 and we’ll find the earliest slot.
Why a Gate Specialist Keeps the Price Honest
A fence company that does gates on the side, or a general repair handyman, prices gate parts and welding by the hour and figures out the failure on arrival. We’re the opposite. Every technician, every tool, and every stocked part is gate-specific. That means fewer return visits, less diagnostic time billed to you, and a part quote that comes from someone who already knows the common failure points of your LiftMaster, FAAC, or Ghost Controls system.
Your gate system is a full lifecycle – the same company that installs it can repair and maintain it years later, so there’s no finger-pointing between an installer and a repair crew. Electric gate repair, including motors, control boards, safety devices, and access systems, is a core capability here, not an outsourced add-on. If you want a broader view of the shop and how we work, start at our home page.
Get a Free Gate Parts & Welding Estimate in Ontario
Before you approve a number, get one that comes from someone who’s opened your operator and inspected the weld. Ontario Gate Company provides free estimates on gate repair, electric gate repair, and gate installation, and we service the full span of operator brands from residential Mighty Mule arms to commercial DoorKing slide operators. Call (855) 707-3634 today and we’ll get your gate back in operation.
Pricing reflects the Ontario market as of 2026. Ontario Gate Company offers free estimates – call (855) 707-3634.
What Our Customers Say
"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
— Michael Rhodes"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, had one with him, and we were moving cars again in under an hour."
— Karen Chen"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
— Adam Whitaker