Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Colton, CA
Gate installation in Colton means building for the Cajon Pass. Wind-driven grit from the Santa Ana wash and the Union Pacific yard settles into every hinge, roller, and post cap, so we plan for that from the first measurement. Ontario Gate Company has served Colton since 2011. We’re a gate-only company: every technician you’ll meet works exclusively on gates and gate automation, spanning the older wrought-iron driveways near downtown, the sliding chain-link on industrial parcels off I-10, and newer ornamental steel in the south tracts. Call (855) 707-3634 for a free estimate.
Why Colton Homes Are Different
Colton sits at the foot of the Cajon Pass and along the Santa Ana River corridor, and that position shapes gate work here in ways that outsiders miss. The seasonal Santa Ana winds pick up gritty alluvial dust from the wash, the rail yard, and the open shoulders of the I-10, then drive it into gate hardware. Bottom-track rollers pack with sand. Hinge pins grind instead of glide. Exposed steel frames pit faster than gates in cities shielded from the pass, and diesel soot from the constant rail traffic leaves a residue that clings to chain-link and track. A routine Colton service call is frequently a de-gritting and re-alignment job before anything has actually failed.
Colton’s housing stock adds another layer. The historic downtown core holds pre-war and mid-century homes with older wrought-iron driveway gates that have been welded and re-welded over the decades. The south and east sides spread into 1970s through 2000s tract development with chain-link and vinyl. Commercial and industrial parcels along the rail corridor carry heavy sliding cantilever and rolling gates that absorb constant vibration. Hot inland summers make steel expand and contract; dry Santa Ana events blast the finish; the occasional winter rain finds ground-level welds and post footings. We diagnose for this city specifically, not for some generic inland California suburb.
Styles & brands we work with
Our Main Colton Services
These are the two calls we get most often from Colton property owners. Each has its own page that goes deeper into what that service costs and covers here.
Gate Repair in Colton
Repair work in Colton usually starts with grit removal, because the pass dust hides the real problem until the track is cleaned and the hinges are freed. From there we deal with sagging frames, seized rollers, snapped chains on commercial sliders, and gates that have dropped off their post hinges. A Colton repair means the gate gets restored to full function, not just temporarily propped up. Get the full breakdown on Gate Repair in Colton.
Electric Gate Repair in Colton
Windblown sand doesn’t stop at the mechanical parts. It gets into control boards, fouls photocells, and packs around limit switches on operators. Electric gate repair here means cleaning contact points, checking safeties, re-terminating connections that vibration from the rail corridor has loosened, and programming fresh limits when the gate no longer knows its own travel. Most general companies decline board work or outsource it. We keep it in-house. Details are on Electric Gate Repair in Colton.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Gate Installation in Colton
Gate installation in Colton has to account for two things right away: what the pass does to hardware, and what your exact property looks like. The older homes near downtown often have narrow driveways and setbacks that demand a compact swing geometry or a slide that doesn’t eat the whole front yard. The newer tracts on the south and east sides give us more room but expose the gate to a straight shot of Santa Ana wind. And commercial parcels along the rail corridor call for heavier rolling or cantilever gates that can shrug off vibration. Whatever we’re installing, we’re sizing it for this city’s grit, heat, and rail vibration from the start. That’s the difference between a gate that lasts and one that becomes a repeat service call. You can see our full installation process on the Gate Installation overview.
Automatic Gate Installation
Signs you need it
A manual gate you have to open in the rain, high-crime block, a rental unit where tenants expect controlled access, or any driveway where backing out onto a busy street makes a manual gate a daily pain.
What it costs in Colton
Automatic gate installation in Colton typically runs from $3,000 to $7,500 for a single swing gate with a mid-grade operator, installed.
How we do it
We measure the driveway and post condition, set or reinforce the posts, mount the operator and arms, wire the control board, install the safety edges and photocells, and run a full test cycle before we call the job finished.
Sliding Gate Installation
Signs you need it
A driveway that tilts uphill from the street, a short setback that rules out a swing gate, a wide commercial opening, or an existing roller track that has become a grit trap.
What it costs in Colton
Sliding gate installation in Colton typically runs $3,500 to $8,000 depending on track length, cantilever requirements, and whether the gate is chain-link, ornamental steel, or solid panel.
How we do it
We lay or rebuild the track bed with proper drainage so pass grit washes out rather than packing in, set the gate frame and rollers, hang and balance the gate, then install the operator and safeties.
What Gate Installation Costs in Colton
| Item | Typical range in Colton |
|---|---|
| Single swing gate with operator | $3,000 – $7,500 |
| Sliding gate with operator | $3,500 – $8,000 |
| Full driveway gate system, dual operator | $6,000 – $12,000 |
Do I need a permit to install a gate in Colton?
Most residential gate installations in Colton don’t require a permit, but if your setback changes, posts are poured, or a new power run is needed, the City of Colton Building Division may want drawings. We handle the paperwork when it’s needed and price it into the estimate.
What’s included in a full automatic gate installation?
A complete installation includes the gate and posts, operator, control board, safety edges, photocells, keypad or remote, power hookup from a licensed electrician where needed, and a final test cycle. You get a written price before any work begins. Call (855) 707-3634 for an exact quote.
Brands We Service in Colton
We service our brands across Colton every week. The most common operators we see here are Viking, Ghost Controls, DoorKing, and Elite, plus their control boards and safeties. We carry common parts for these makes in our service vehicles, so a Colton repair is frequently completed on the first trip rather than parked waiting for a shipped part.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Colton, CA
| Service | Typical range in Colton |
|---|---|
| Gate repair inspection and diagnosis | $80 – $150 |
| Hinge replacement | $150 – $400 |
| Roller replacement | $180 – $500 |
| Track cleaning and realignment | $150 – $350 |
| Electric gate motor replacement | $800 – $2,000 |
| Control board replacement | $500 – $1,500 |
| Safety edge or photocell replacement | $250 – $600 |
| Single swing gate with operator | $3,000 – $7,500 |
| Sliding gate with operator | $3,500 – $8,000 |
| Full driveway gate system | $6,000 – $12,000 |
Colton pricing gets pushed up by two things: pass grit that has compounded a simple repair into a full track and roller rebuild, and older gates near downtown that need post reinforcement before any new hardware goes on. Every job gets an upfront written price, agreed before work starts, so your invoice matches the estimate.
Neighborhoods We Serve in Colton
We cover the full 92324 ZIP and every part of Colton inside it. That includes the historic downtown core, the south and east tract developments, and the industrial and rail-adjacent parcels along the I-10 corridor.
- Historic downtown Colton
- South Colton
- East Colton
- Reche Canyon area
- I-10 / rail corridor industrial parcels
Response time across Colton is usually same-day for diagnosis, with most repairs finished the same visit. Larger installations are scheduled after a free on-site measure.
Service Area – Cities Near Colton
Ontario Gate Company is based in Ontario, but Colton is inside our regular service loop. We also handle work in Grand Terrace, CA, Highgrove, CA, Loma Linda, CA, and Rubidoux, CA. If your property is near the Colton border, call and we’ll confirm coverage before you schedule.
Serving Colton, CA — Our Local Coverage Area
We’re based in the Colton area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Colton
Most Colton repair calls get same-day or next-morning service. We route technicians in the Inland Empire daily, and Colton is inside our regular loop. If the gate is off its track or stuck open, we prioritize it because the security hole won’t close itself. Call (855) 707-3634 to ask about today’s schedule.
We’ll handle the permit paperwork when the City of Colton wants it, which is usually only for new power runs or foundation changes. HOA approvals are shared responsibility: we provide the specs, schematic, and panel design your HOA asks for, and you submit it. That keeps the gate from getting flagged after it’s already built.
Yes. Some of the downtown Colton wrought-iron gates date back before the city built the 215 connector, and we service them carefully. When a hinge or post has rusted through, we weld the repair or build a new post rather than forcing a modern retrofit that doesn’t fit the gate’s original geometry. The quote reflects the condition of the steel, not a standard book price.
If your gate is sticking, sagging, or dead in Colton, call Ontario Gate Company at (855) 707-3634. We’ll give you a free estimate, written upfront, and a straight answer about what we’re fixing.
What happens when you call
- 1A real person answersNo phone trees — talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you — the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Colton Customers Say
"Repair is holding. He was quite a bit later than the window I was given, and the office didn't call me about it, I had to call them. The work itself was done well once he got here."
— Beatriz Salazar"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
— Alma Garcia"The loop detector under the driveway had failed and residents were stuck holding the button. He traced it, found the break, and had the exit loop reading cars again the same visit."
— Yusuf Aziz